Hello all,
I see in pictures that some appear to carry their mast in a PVC pipe. This seems like a great idea to me. Since I don't have my boat yet, can anyone tell me what diameter pipe you used and if the boom fits in there also?
Thanks
Hi Monona,
Welcome to the site. I can't say I've seen anyone carry a mast in a PVC pipe, but have seen folks carry the boom there (in general, not a legacy which I've never eyes upon).
With that said, doesn't the legacy have the boom tender system as standard? I believe the mast, sail and boom would stay attached always with the exception of taking the sail off once in a while to clean, travel long distances, mend, etc. A crutch would be used aft to hold the affair up. At least that is my understanding of the system and the benefit is you just untie it from the crutch, clear the lines and shrouds, then raise the mast without much fuss. I well could be wrong here, so let another actual legacy owner guide you the right direction.
With that said, I don't see a reason to hold the mast in a PVC pipe. It would seriously complicate rigging IMO.
Sounds like you're ordering a new one. Very cool..enjoy her, Com-pacs are really nice little boats. Just stay away from the 19's or the Eclipse or you'll have the dreaded incurable 3 foot-itus!
Thank you so much for the information. Makes a lot of sense to me. And I should have been more specific, the boat is new to me. It is a 2008 Legacy that has only been out on the water about 6 times. Stored indoors all other times - so it looks really good. When I went to look at it, I didn't seem to have a crutch. I'll need to e-mail the current owner to find out.
Again, thank you for your reply. Really happy to have found this forum.
The Legacy doesn't need a crutch to hold the mast. That's what the rear arch is for. And yes, the boom generally stays attached to the mast during transport.
I would think it would take a pretty large diameter PVC pipe to hold the mast with the head and foot hardware.
Kahp, thanks, I forgot about that arch around the aft end. That will do the trick.
Some padding or carpet to keep scratching down and bungie cord or other wraps would secure it.
Com-pac sure has made their newer boats easy to use.
Thanks all!
Recommend no bungee cords! They can break and put out eyes. I carry any number of short lengths of lines to make things fast. Safe and eazy peazy.
Smooth sailing!
Quote from: CayugaSailor on December 08, 2017, 07:28:09 AM
Recommend no bungee cords! They can break and put out eyes. I carry any number of short lengths of lines to make things fast. Safe and eazy peazy.
Smooth sailing!
I do the same. I use short lengths for all kinds of lashing jobs, which reminds me I need to cut some more. I keep finding more uses for them.
I've been toying with the idea of using a PCV pipe to house my roller furler headstay when trailering my Eclipse. That may be a better use for a piece of PVC. I want to keep the jib on it but I don't like the idea of leaving it flapping in the wind, nor do I like storing it in an arch inside the cockpit. Same concept would apply to the Legacy. If I figure this out and come up with a good mount I'll post pics.
The idea came to me when I got my new gin pole from Hutchins that was shipped in a 2 1/2" PCV pipe. I band clamped it right on the trailer, cemented a cap on one end, and drilled a hole through another cap and the pipe with a removable pin on the other end. Now it's nice and cozy and protected, easy to access, and not taking up room in the boat.
Slode: I did the exact same thing one year when I removed the mast and furler from my 23. I needed to service the mast so I brought it home and wanted to check the turnbuckle under the CDI furler. I just slid the whole thing into the 5" PVC pipe. Kind of a lot of work that I didn't need to do every year but it worked.
Thanks all,
If any of you have pictures of your set up, I'd be really interested in seeing them. Thanks!